Post Install Steps for x2amd002-v1- image

This is for the Fall 2013 PC Workstations (dual-boot Windows 7/Ubuntu 12.04)

Phil says these are the extra or changed steps:

  • new Win7 activation code needed: Windows7LicenseKey
  • register Office through the Control Panel , Programs applet.
  • ssh should be licensed, if not, license file is in c:\drivers
  • ubuntu scripts should also be in c:\drivers

Immediately Post-Imaging

Windows

* IMPORTANT NOTE: Do NOT restart the computer except where noted

Perform Initial Setup

  1. Boot, Windows will perform first run setup, may take a while (will install drivers)
  2. Will then reboot
  3. Windows' Set Up Windows wizard will appear
    • Page One:
      • Change country to Canada -> Next
    • Page Two:
      • Username: Temp
      • Computer name: eg: rsg-pc070 -> Next
    • Page three:
      • Password: use cscf-op or cscf-adm password
      • Hint: "Fall 2013 cscf-op" (or whatever is relevant)
    • Page Four:
      • Accept the license -> Next
    • Page Five:
      • Install Important Updates Only
    • Page Six:
      • Set Time zone: UTC-05:00 Eastern Time (US & Canada)
      • Check box: Automatically adjust clock for daylight savings time
      • Check Date/Time: Adjust if necessary -> Next
    • Page Seven: (Only if Wireless card present)
      • If asked about connecting to a wireless network -> Click Skip
    • Page Seven / Seven.One:
      • Select Work Network
    • Setup Will continue after restarting

Activate Windows and Office

  1. Activate Windows
    • If Asked on boot
      • Click Activate Now
      • Click Activate Windows online now
      • Click close
    • Otherwise
      • Start -> Control Panel -> System and Security -> System
      • At the bottom, Click the link to Activate Windows
      • Click Activate Windows online now
      • Click close
      • Close the Control Panel
  2. Activate Office

Correct Hardware Detection Problems

  1. If Screen resolution is too low (Looks really bad)
    • Start -> Control Panel -> Adjust Screen Resolution
    • Change resolution to the highest one -> click apply
    • Windows will change the resolution and ask if you want to keep it:
      • If the screen goes black, wait 15 seconds
        • Try the next highest and repeat
      • If the box shows up, and the lettering looks normal -> Click "Keep Changes"
        • If the lettering looks funny (out of proportion) try the next highest and repeat
    • CLose the Control Panel

Update Software

  1. If at any point Windows Update pops up a box in the lower right asking to restart the computer
    • change 10 minutes to 4 hours, click postpone
  2. If Java Updater Requests permission
    • Click Yes
    • When the balloon appears on the Java icon click it
    • Click Install
    • Click Install (Again!)
    • Wait a few minutes for Java to install
    • If it asks about install Extras (e.g. Ask Toolbar)
      • Uncheck the Box marked install
      • Click Next
    • Java will now install, wait patiently
    • Click Close

Finish With Windows Update And Clean Up

  1. Windows Update may appear asking to restart
    • Click Restart now
    • Wait patiently while the computer restarts
      • Note: If the Force close option comes up listing Windows Update, wait, it will close on its own
  2. If Windows Update does not appear (if it has not shown up after about five minutes, it's not going to), then log out
    • Click Start
    • Hover over the arrow next to shutdown
    • Click Log out
  3. Windows may reboot several times
  4. Windows will show to the login screen
    • Login as either cscf-op or cscf-admin
  5. Delete the Temp account
    • Open Start -> Control Panel -> User Accounts and Family Safety -> Add or remove user accounts
    • Click on Temp
    • Click Delete the account -> Delete Files -> Delete Account
    • Close the Control Panel
  6. Shutdown the computer or reboot into Linux (Done!)

Linux

Boot Computer And Log In

  1. Boot the Computer
    • Windows Bootloader choose Ubuntu 12.04 LTS
    • GRUB Choose first Ubuntu option
  2. Will present you with a login screen, log in as either cscf-op or cscf-adm using Fall 2013 password

Set Hostname

  1. Press Ctrl+Alt+T to open a terminal
  2. Type "sudo vim /etc/hostname", press enter
  3. Enter the same password you used to log in
  4. change scspcxxx to rsg-pc### (substitute 3 digit number from hostname for ###)
  5. Type "sudo vim /etc/hosts", press enter
  6. Change scspcxxx to rsg-pc### (substitute 3 digit number from hostname for ###)
Script to change Hostname update

Note: this script will change the following files: /etc/hosts /etc/hostname /etc/mailname /etc/postfix/main.cf /var/spool/postfix/etc/ /var/lib/chdp/dhclient
You will be updating the system mail name so that outgoing email notices will work correctly

  1. change into the ubuntu-scripts directory under the cscf-adm account
  2. ./fixhost newhostname - whith the .cs

Fix /etc/ssh/ssh_config

  • Update the line that has ``'' to just use regular double quotes

Fix Upgrade Policy and Update

  1. Change upgrade policy to never upgrade
    • Still in the terminal, type "software-properties-gtk", press enter
    • On the Updates Tab, change Release Upgrade menu to Never
    • On the Other Software tab
      • Scroll down to just below the "Canonical Partners" listings (just over half way)
      • Uncheck the four lines starting with "http://ppa.launchpad.net/mozillateam/"
    • Click close
  2. Install updates
    • Type "apt-get update", press enter
    • If the Update Manager opens, close or ignore it
    • Type "apt-get dist-upgrade", press enter
    • If prompted to install updates, type "y", enter
    • If prompted to replace a config file, press enter

Finish

  1. Shutdown the Computer
    • Settings / Power Menu (Top right) -> Shutdown -> Shutdown

Before Deploying

Windows

  1. Add user to local Administrators group

Linux

AD setup

Initial setup
  1. Run Mike Gore's join-ad script
final AD setup
  1. vi /etc/security/access.conf and add user (or users_groupname)
  2. vi /etc/sudoers and add user (and, possibly, admin_groupname)

update

  1. apt-get update && apt-get dist-upgrade
    • when queried, do not replace the LDAP/common-auth !
    • smb.conf - it will ask for a newer version - don't do it!

Setup networking

  1. ONA

update inventory

  1. remove old machines and equipment
  2. add new machine
Topic revision: r5 - 2013-09-13 - LawrenceFolland
 
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2019 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback