 |
» |
|
|
|
|
|
|
|
|
HP ProLiant DL380 G5 Storage Server - Specifications
System specifications
System Specifications
| Specification
|
Description
|
|---|
| Rack Height
|
2U |
| Number of Configured Processors
|
1 |
| Processor Capacity
|
2 |
| Maximum Memory
|
32 GB |
| Memory Protection
|
Advanced ECC |
| Memory Note
|
PC2-5300 |
| Power Supply
|
Dual hot-plug power supply |
| Redundant Power Supply
|
Standard |
| Redundant Fans
|
Standard |
| Configured Storage Capacity
|
N/A |
| Optical Drive
|
DVD+R/RW 8X Slim |
| Number of Users
(Starting) |
200 |
| Number of Users
(Maximum |
400 |
| Warranty
(Parts-Labor-Onsite) |
3-3-3 |
Component specifications
Smart Array P400
Controller
| Sub-Component
|
Description
|
|---|
| Disk Drive and Enclosure
|
3G SAS (Serial Attached SCSI) |
| Interface
|
1.5 G SATA (Serial Advanced Technology Attachment) |
| SAS Connectors
|
2 internal (SFF8484) x4 wide port connectors |
| Cache Memory Speed
|
DDR2-533 MHz with 40 or 72-bit wide bus provides up to 4.2 GB/s
maximum bandwidth. |
| Server Interface
|
x8 2.5G PCIe provides 2 GB/s maximum bandwidth. |
| SAS Speed
|
x8 3G SAS provides 2.4 GB/s maximum bandwidth. |
| Cache Memory
|
40-bit 256 MB cache (72-bit 512 MB module upgrades available); ECC
protection, battery-backed, and transportable |
| Logical Drives Supported
|
Up to 32 logical drives |
| Maximum Logical Drive
Capacity
|
3 TB (6 x 500 GB) |
| Host Memory Addressing
|
64-bit, supporting greater than 4 GB server memory space |
| RAID Support
|
RAID 6 with ADG (Advanced Data Guarding) requires Battery Backed Write
Cache Upgrade
RAID 5 (Distributed Data Guarding)
RAID 1+0 (Striping & Mirroring)
RAID 0 (Striping) |
Two Embedded NC373i
Multifunction Server
Adapters
| Sub-Component
|
Description
|
|---|
| Network Interface
|
10 Base-T/100 Base-TX/1000 Base-TX |
| Compatibility
|
IEEE 802.3 10 Base-T |
| IEEE 802.3ab 1000 Base-T |
| IEEE 802.3u 100 Base-TX |
| Data Transfer Method
|
PCI Express, four lanes (x4) |
| Network Transfer Rate
|
10 Base-T (Half-Duplex) |
10 Mb/s |
| 10 Base-T (Full-Duplex) |
20 Mb/s |
| 100 Base-TX (Half-Duplex) |
100 Mb/s |
| 100 Base-TX (Full-Duplex) |
200 Mb/s |
| 1000 Base-TX (Half and
Full-Duplex) |
2000 Mb/s |
| Connector
|
Two RJ-45 |
| Cable Support
|
10 Base-T |
Categories 3, 4 or 5 UTP;
up to 328 feet (100 meters) |
| 100 Base-TX |
Category 5 or higher UTP;
up to 328 feet (100 meters) |
| 1000 Base-TX |
Category 5 or higher UTP;
up to 328 feet (100 meters) |
|
NOTE:
|
The NC373i Multifunction Gigabit Server Adapters require installation of the Microsoft Windows Server 2003 Scalable
Networking Pack (a free download from Microsoft) to enable TCP Chimney offload, Receive-side Scaling (RSS), and Network Direct
Memory Access (NetDMA) features. |
Physical specifications
Physical Specifications
| Specification
|
Description
|
|---|
Dimensions
(HxWxD)
(with feet/bezel) |
3.38 x 17.54 x 26.01 inches (8.59 x 44.54 x 66.07 cm) |
| Weight
(approximate) |
Maximum
|
60 lb (27.22 kg) |
| Minimum
|
47.18 lb (20.41 kg) |
Electrical specifications
Electrical Specifications
| Specification
|
Description
|
|---|
| Input Requirements
(per power supply) |
Rated Line Voltage
|
100-132 VAC, 200-240 VAC |
| Rated Input Current
|
10 A (100 VAC), 10 A (120 VAC), 6.1 A (200 VAC) |
| Rated Input Frequency
|
50 to 60 Hz |
| Rated Input Power
|
1000/1056/1205 Watts |
| BTU Rating
|
BTU/HR
|
3490/3680/4150 |
| Power Specifications
|
To review typical system power ratings use the Active Answers Power
Calculator which is available via the online tool located at URL:
http://h30099.www3.hp.com/configurator/powercalcs.asp
.
To drill down to calculators:- Click ProLiant Servers
- Click on the server of interest. (Example
: DL380 G5)
- Click Power Calculator
. (You may need to scroll down to see it.)
|
| Power Supply Output
Power
(per power supply) |
Rated Steady-State Power |
800/850/1000 Watts |
| Maximum Peak Power |
800/850/1000 Watts |
Environmental specifications
Environmental Specifications
| Specification
|
Description
|
|---|
| Temperature Range
|
Operating
|
50 degrees to 95 degrees F (10 degrees to 35 degrees C) at sea level with an
altitude de-rating of 1.8 degrees F per 1000 feet (1.0 degrees C
per 304.8 meters) to 10,000 feet (3048 meters) no direct
sunlight allowed. Maximum rate of change is 18
degrees F/Hr (10 degrees C/Hr). Upper operating limit is 10,000
feet (3,048 meters) or 70 Kpa/10.1 psia.
System performance may be reduced if operating
with a fan fault or above 30 degrees C. |
| Non-operating
|
-22 degrees to 140 degrees F (-30 degrees to 60 degrees C) Maximum rate of
change is 36 degrees F/Hr (20 degrees C/Hr). Upper nonoperating
limit is 30,000 feet (9,144 meters) or
30.3KPa/4.4 psia. |
| Maximum Wet Bulb
Temperature
|
101.7 degrees F (38.7 degrees C) |
| Relative Humidity
(non-condensing) |
Operating
|
10% to 90% relative humidity (Rh), 28 degrees C
maximum wet bulb temperature. |
| Non-operating
|
5% to 95% relative humidity (Rh), 38.7 degrees C
maximum wet bulb temperature. |
| Acoustic Noise
|
Idle Minimum
(Fixed Disk
Drives Spinning) |
| WAd (BELS) |
6.1 |
| pAm (dBA) |
44 |
| Operating Minimum
(Random Seeks to Fixed
Disks) |
| WAd (BELS) |
6.1 |
| pAm (dBA) |
44 |
Link to the overview of the product
|
|
Printable version
